Human FOXP3/Forkhead box protein P3 ELISA Kit

Product Name:	Human FOXP3 / Forkhead box protein P3 ELISA Kit
Product Code:	HUFI01661
Size:	96 Assays
Alias:	FOXP3, Forkhead box protein P3, DIETER, IPEX, JM2, PIDX, SCURFIN, XPID, AIID, forkhead box P3, FOXP3delta7, immune dysregulation, polyendocrinopathy, enteropathy, X-linked, Scurfin, XPIDpolyendocrinopathy, enteropathy, X-linked
Detection method:	Sandwich ELISA, Double Antibody
Application:	This immunoassay kit allows for the in vitro quantitative determination of Human FOXP3 concentrations in serum plasma and other biological fluids.
Sensitivity:	0.188ng/ml
Range:	0.313-20ng/ml
Storage:	4°C for 6 months
Note:	For Research Use Only

Recovery:

Matrices listed below were spiked with certain level of Human FOXP3 and the recovery rates were calculated by comparing the measured value to the expected amount of Human FOXP3 in samples.

Matrix	Recovery range(%)	Average(%)
serum(n=5)	92-100	97
EDTA plasma(n=5)	92-103	96
UFH plasma(n=5)	90-105	97

Linearity:

The linearity of the kit was assayed by testing samples spiked with appropriate concentration of Human FOXP3 and their serial dilutions. The results were demonstrated by the percentage of calculated concentration to the expected.

Sample	1:2	1:4	1:8
serum(n=5)	85-103%	85-99%	91-103%
EDTA plasma(n=5)	84-100%	87-97%	83-97%
UFH plasma(n=5)	81-100%	81-100%	80-100%

CV(%):

Intra-Assay: CV<8%
Inter-Assay: CV<10%

Component	Quantity	Storage
ELISA Microplate (Dismountable)	8×12 strips	4°C for 6 months
Lyophilized Standard	2	4°C/-20°C
Sample/Standard Dilution Buffer	20ml	4°C
Biotin-labeled Antibody(Concentrated)	120ul	4°C (Protect from light)
Antibody Dilution Buffer	10ml	4°C
HRP-Streptavidin Conjugate(SABC)	120ul	4°C (Protect from light)
SABC Dilution Buffer	10ml	4°C
TMB Substrate	10ml	4°C (Protect from light)
Stop Solution	10ml	4°C
Wash Buffer(25X)	30ml	4°C
Plate Sealer	5	-

Other materials and equipment required:

Microplate reader with 450 nm wavelength filter
Multichannel Pipette, Pipette, microcentrifuge tubes and disposable pipette tips
Incubator
Deionized or distilled water
Absorbent paper
Buffer resevoir

Uniprot

Q9BZS1

UniProt Protein Function:	FOXP3: Probable transcription factor. Plays a critical role in the control of immune response. Interacts with IKZF3. 3 isoforms of the human protein are produced by alternative splicing.
UniProt Protein Details:	Protein type:Transcription factor; C2H2-type zinc finger protein; DNA-binding; Cell cycle regulation Chromosomal Location of Human Ortholog: Xp11.23 Cellular Component: cytoplasm; nucleus Molecular Function:histone acetyltransferase binding; histone deacetylase binding; NFAT protein binding; protein binding; protein homodimerization activity; sequence-specific DNA binding; transcription factor activity Biological Process: CD4-positive, CD25-positive, alpha-beta regulatory T cell lineage commitment; inhibition of CREB transcription factor; inhibition of NF-kappaB transcription factor; negative regulation of cell proliferation; negative regulation of cytokine biosynthetic process; negative regulation of cytokine secretion; negative regulation of histone deacetylation; negative regulation of immune response; negative regulation of interferon-gamma production; negative regulation of interleukin-10 production; negative regulation of interleukin-17 production; negative regulation of interleukin-2 biosynthetic process; negative regulation of interleukin-2 production; negative regulation of interleukin-4 production; negative regulation of T cell cytokine production; negative regulation of T cell proliferation; negative regulation of transcription factor activity; negative regulation of transcription, DNA-dependent; positive regulation of CD4-positive, CD25-positive, alpha-beta regulatory T cell differentiation; positive regulation of histone acetylation; positive regulation of transcription from RNA polymerase II promoter; positive regulation of transcription, DNA-dependent; regulation of T cell anergy; response to virus; T cell activation Disease: Diabetes Mellitus, Insulin-dependent; Immunodysregulation, Polyendocrinopathy, And Enteropathy, X-linked
NCBI Summary:	The protein encoded by this gene is a member of the forkhead/winged-helix family of transcriptional regulators. Defects in this gene are the cause of immunodeficiency polyendocrinopathy, enteropathy, X-linked syndrome (IPEX), also known as X-linked autoimmunity-immunodeficiency syndrome. Alternatively spliced transcript variants encoding different isoforms have been identified. [provided by RefSeq, Jul 2008]
UniProt Code:	Q9BZS1
NCBI GenInfo Identifier:	14548061
NCBI Gene ID:	50943
NCBI Accession:	Q9BZS1.1
UniProt Secondary Accession:	Q9BZS1,O60827, Q14DD8, Q4ZH51, A5HJT1, B7ZLG0, B9UN80
UniProt Related Accession:	Q9BZS1
Molecular Weight:	44,407 Da
NCBI Full Name:	Forkhead box protein P3
NCBI Synonym Full Names:	forkhead box P3
NCBI Official Symbol:	FOXP3
NCBI Official Synonym Symbols:	JM2; AIID; IPEX; PIDX; XPID; DIETER
NCBI Protein Information:	forkhead box protein P3
UniProt Protein Name:	Forkhead box protein P3
UniProt Synonym Protein Names:	Scurfin
Protein Family:	Forkhead box protein
UniProt Gene Name:	FOXP3
UniProt Entry Name:	FOXP3_HUMAN

*Note: Protocols are specific to each batch/lot. For the correct instructions please follow the protocol included in your kit.

Before adding to wells, equilibrate the SABC working solution and TMB substrate for at least 30 min at 37°C. When diluting samples and reagents, they must be mixed completely and evenly. It is recommended to plot a standard curve for each test.

Step	Protocol
1.	Set standard, test sample and control (zero) wells on the pre-coated plate respectively, and then, record their positions. It is recommended to measure each standard and sample in duplicate. Wash plate 2 times before adding standard, sample and control (zero) wells!
2.	Aliquot 0.1ml standard solutions into the standard wells.
3.	Add 0.1 ml of Sample / Standard dilution buffer into the control (zero) well.
4.	Add 0.1 ml of properly diluted sample ( Human serum, plasma, tissue homogenates and other biological fluids.) into test sample wells.
5.	Seal the plate with a cover and incubate at 37 °C for 90 min.
6.	Remove the cover and discard the plate content, clap the plate on the absorbent filter papers or other absorbent material. Do NOT let the wells completely dry at any time. Wash plate X2.
7.	Add 0.1 ml of Biotin- detection antibody working solution into the above wells (standard, test sample & zero wells). Add the solution at the bottom of each well without touching the side wall.
8.	Seal the plate with a cover and incubate at 37°C for 60 min.
9.	Remove the cover, and wash plate 3 times with Wash buffer. Let wash buffer rest in wells for 1 min between each wash.
10.	Add 0.1 ml of SABC working solution into each well, cover the plate and incubate at 37°C for 30 min.
11.	Remove the cover and wash plate 5 times with Wash buffer, and each time let the wash buffer stay in the wells for 1-2 min.
12.	Add 90 Âµl of TMB substrate into each well, cover the plate and incubate at 37°C in dark within 10-20 min. (Note: This incubation time is for reference use only, the optimal time should be determined by end user.) And the shades of blue can be seen in the first 3-4 wells (with most concentrated standard solutions), the other wells show no obvious color.
13.	Add 50 Âµl of Stop solution into each well and mix thoroughly. The color changes into yellow immediately.
14.	Read the O.D. absorbance at 450 nm in a microplate reader immediately after adding the stop solution.

When carrying out an ELISA assay it is important to prepare your samples in order to achieve the best possible results. Below we have a list of procedures for the preparation of samples for different sample types.

Sample Type	Protocol
Serum	If using serum separator tubes, allow samples to clot for 30 minutes at room temperature. Centrifuge for 10 minutes at 1,000x g. Collect the serum fraction and assay promptly or aliquot and store the samples at -80°C. Avoid multiple freeze-thaw cycles. If serum separator tubes are not being used, allow samples to clot overnight at 2-8°C. Centrifuge for 10 minutes at 1,000x g. Remove serum and assay promptly or aliquot and store the samples at -80°C. Avoid multiple freeze-thaw cycles.
Plasma	Collect plasma using EDTA or heparin as an anticoagulant. Centrifuge samples at 4°C for 15 mins at 1000 × g within 30 mins of collection. Collect the plasma fraction and assay promptly or aliquot and store the samples at -80°C. Avoid multiple freeze-thaw cycles. Note: Over haemolysed samples are not suitable for use with this kit.
Urine & Cerebrospinal Fluid	Collect the urine (mid-stream) in a sterile container, centrifuge for 20 mins at 2000-3000 rpm. Remove supernatant and assay immediately. If any precipitation is detected, repeat the centrifugation step. A similar protocol can be used for cerebrospinal fluid.
Cell culture supernatant	Collect the cell culture media by pipette, followed by centrifugation at 4°C for 20 mins at 1500 rpm. Collect the clear supernatant and assay immediately.
Cell lysates	Solubilize cells in lysis buffer and allow to sit on ice for 30 minutes. Centrifuge tubes at 14,000 x g for 5 minutes to remove insoluble material. Aliquot the supernatant into a new tube and discard the remaining whole cell extract. Quantify total protein concentration using a total protein assay. Assay immediately or aliquot and store at ≤ -20 °C.
Tissue homogenates	The preparation of tissue homogenates will vary depending upon tissue type. Rinse tissue with 1X PBS to remove excess blood & homogenize in 20ml of 1X PBS (including protease inhibitors) and store overnight at ≤ -20°C. Two freeze-thaw cycles are required to break the cell membranes. To further disrupt the cell membranes you can sonicate the samples. Centrifuge homogenates for 5 mins at 5000xg. Remove the supernatant and assay immediately or aliquot and store at -20°C or -80°C.
Tissue lysates	Rinse tissue with PBS, cut into 1-2 mm pieces, and homogenize with a tissue homogenizer in PBS. Add an equal volume of RIPA buffer containing protease inhibitors and lyse tissues at room temperature for 30 minutes with gentle agitation. Centrifuge to remove debris. Quantify total protein concentration using a total protein assay. Assay immediately or aliquot and store at ≤ -20 °C.
Breast Milk	Collect milk samples and centrifuge at 10,000 x g for 60 min at 4°C. Aliquot the supernatant and assay. For long term use, store samples at -80°C. Minimize freeze/thaw cycles.